Kernel version 2.6.32 or later. [This depends on architecture though, we need to have specific builder for this.] Linux/ARMv5 requires much newer kernels, at least v3.1 (for __kuser_cmpxchg64).
We don't support CentOS 5. The kernel is too old (2.6.18).
For little-endian MIPS64, kernel version 4.1 is known to fail, and 4.8 works.
If you are using tinyconfig (e.g. make tinyconfig) for embedded systems, you will also almost certainly enable printk in the kernel as well as a console; we will not include those generic options here. For Go, you must also enable CONFIG_FUTEX and CONFIG_EPOLL.
On arm64, an out of date (lower than version 2.33) ld.gold may cause shared library tests to fail (see https://github.com/golang/go/issues/28334).
For Go 1.10: Windows XP (w/ Service Pack 3) or higher.
For Go 1.11 and later: Windows 7 and higher or Windows Server 2008 R2 and higher. We test on Windows Server 2008 R2, 2012 R2, and 2016, which are roughly Windows 7, Windows 8.1, and Windows 10.
For Go 1.21 and later: Windows 10 and higher or Windows Server 2016 and higher.
macOS Sierra 10.12 or higher requires Go 1.7.1 or above.
macOS Monterey 12 or higher requires Go 1.11 or above.
Go 1.15 and later only support macOS Sierra 10.12 or newer; see https://go.dev/doc/go1.15#darwin.
Go 1.17 and later only support macOS High Sierra 10.13 or newer; see https://go.dev/doc/go1.17#darwin.
Go 1.21 and later will support macOS Catalina 10.15 or newer; see https://go.dev/doc/go1.20#darwin.
We have builders for macOS 10.14 through macOS 13 as of 2023-05-31.
The current officially supported -stable versions only.
Generally only the latest release version only. We have a builder, but it's not the most stable of our ports.
See Go on FreeBSD for supported FreeBSD/Architecture/Go versions matrix.
There are known NetBSD bugs (including kernel crashes) up to the current NetBSD 7.1. There is a reported fix in NetBSD 7.1.1 but it‘s unverified as of 2017-07-10, as we’re not running builders again yet. See https://tip.golang.org/doc/go1.9#known_issues and https://github.com/golang/go/issues/20852
illumos (former OpenSolaris 10) based distributions or Oracle Solaris 11+.
iOS 12 or later.
For some architectures, Go supports compiling to specific microarchitectures using environment variables, e.g. GOAMD64 for go1.18 and later. Binaries will check at startup whether the requested microarchitecture level is supported. For example, a binary built with GOAMD64=v3 will fail on a CPU that doesn't have LZCNT support.
Various microarchitecture levels and the environment variables used to select them are described with each architecture.
The build cache understands the microarchitecture environment variables and does not require any cleaning if you change them.
While performance is expected to improve when a higher minimum microarchitecture is requested, this might not be true in all cases. Benchmark your performance-critical code to verify performance improvements.
Until Go 1.17, the Go compiler always generated x86 binaries that could be executed by any 64-bit x86 processor.
Go 1.18 introduced 4 architectural levels for AMD64. Each level differs in the set of x86 instructions that the compiler can include in the generated binaries:
Setting, for example, GOAMD64=v3, will allow the Go compiler to use AVX2 instructions in the generated binaries (which may improve performance in some cases); but these binaries will not run on older x86 processors that don't support AVX2.
The Go toolchain may also generate newer instructions, but guarded by dynamic checks to ensure they‘re only executed on capable processors. For example, with GOAMD64=v1, math/bits.OnesCount will still use the POPCNT instruction if CPUID reports that it’s available. Otherwise, it falls back to a generic implementation.
The Go toolchain does not currently generate any AVX512 instructions.
The race detector is not supported on platforms that do not provide SSE3.
Note that processor is a simplification in this context. In practice, support from the entire system (firmware, hypervisor, kernel) is needed.
See section Microarchitecture support for hints on how to use microarchitecture environment variables like GOAMD64.
See https://go.dev/doc/install/source#environment
See https://go.dev/doc/install/source#environment
Until Go 1.23, the Go compiler always generated ARM64 binaries that could be executed by any ARMv8-A processor.
Go 1.23 introduced a new GOARM64 environment variable, which specifies the minimum target version of the ARM64 architecture at compile time. Allowed values are v8.{0-9} and v9.{0-5}. This may be followed by an option specifying extensions implemented by target hardware. Valid options are ,lse and ,crypto.
Setting, for example, GOARM64=v8.0,lse, will allow the Go compiler to use LSE instructions in the generated binaries (which may improve performance in some cases); but these binaries will not run on older ARM64 processors that don’t support LSE.
The Go toolchain may also generate newer instructions, but guarded by dynamic checks to ensure they’re only executed on capable processors.
The GOARM64 environment variable defaults to v8.0.
POWER5 and above. Starting with Go 1.9, only POWER8 and above are supported.
POWER8 and above.
MIPS III or higher. Builder is using MIPS64r2.
MIPS III or higher in little endian mode.
z13
MIPS32r1
rv64g (rv64imafd)
For programs using cgo, gcc 4.6 or newer is required.